top of page

Industrial Waste Heat Recovery: How a USD 68 Billion Market Turns Lost Heat Into Power

Writer: Strategic Revenue Insights
Strategic Revenue Insights
Nov 13
11 min read
Industrial waste heat recovery: how a USD 68 billion market turns lost heat into power, Strategic Revenue Insights

Executive summary. Every cement kiln, steel furnace, glass tank and refinery heater sends a large share of the fuel it burns out of the stack as hot gas. For most of industrial history that heat was simply lost. Carbon prices, efficiency mandates and higher energy costs are turning it into an asset. Strategic Revenue Insights values the global industrial waste heat recovery systems market at USD 68.00 billion in 2025 and forecasts USD 150.94 billion by 2035, an 8.3 percent compound annual growth rate and a 2.2x expansion. Heat exchangers remain the largest technology, Asia Pacific is the largest and fastest growing region, and energy cost and carbon pricing is the main driver. The mix is shifting from simple heat exchange toward power generation and lower temperature heat. This article sets out five lessons from the equipment makers and plant operators moving first, with takeaways for strategy, technology, sales, product and revenue.


The structure of the market shows where the money sits today and where it is moving. Strategic Revenue Insights' Industrial Waste Heat Recovery Systems Market research finds that heat exchangers hold 46.00 percent of 2025 sales, steam Rankine cycle and organic Rankine cycle systems hold 22.00 percent each, thermoelectric generators hold 8.00 percent and Kalina cycle systems 2.00 percent. By application, heat-to-heat leads at 46.00 percent, heat-to-power holds 36.00 percent and preheating 18.00 percent. By temperature, medium temperature heat from 230 to 650 C leads at 41.00 percent, low temperature heat below 230 C holds 38.00 percent and high temperature heat above 650 C holds 21.00 percent. By end use, steel and metals lead at 22.00 percent, ahead of chemicals and petrochemicals at 21.00 percent and cement at 17.00 percent.


Growth stays close to 8.3 percent a year because capital projects follow industrial investment cycles. But within that steady total, SRI's research shows a clear rotation: heat-to-power grows faster than heat-to-heat, low temperature heat grows faster than medium and high, and cement and glass grow faster than steel.


Why the Industrial Waste Heat Recovery Market Is Entering a New Phase


Three structural forces are converging.


Carbon has a price, and wasted heat now carries it. SRI's research identifies energy cost and carbon pricing as the largest driver, adding 2.6 percentage points to annual growth. Every unit of heat recovered is a unit of fuel not burned and a tonne of carbon not paid for. In regions with carbon markets, that changes the payback on recovery equipment from a long-term efficiency project into a near-term cost reduction. The same pressure is driving the shift to low-carbon cement and carbon capture at the kiln, and heat recovery is usually the cheapest first step on that path.


Efficiency is becoming a rule, not a choice. Efficiency mandates add 2.2 points. Governments increasingly require large energy users to audit and act on their energy losses, and recovered heat is one of the most measurable ways to show progress.


Technology has opened lower temperatures. Low temperature power technology and heavy industry expansion add the rest of the growth. Organic Rankine cycle units and thermoelectric generators can turn heat that was once too cool to use into electricity, which widens the pool of recoverable energy across almost every industrial site.


On the other side, high upfront cost and payback risk remove 1.0 point and site integration complexity removes 0.8 points. The net effect is steady growth with a changing mix.


Industrial waste heat recovery market data snapshot: USD 68 billion in 2025 to USD 150.94 billion by 2035 at 8.3 percent CAGR, with heat-to-power growth, organic Rankine cycle growth and Asia Pacific share

Five Lessons From the Companies Moving First


The equipment makers, engineering firms and plant operators turning waste heat into revenue share a recognisable pattern. We have distilled it into five lessons, each followed by a takeaway for a specific leadership function.


Lesson 1: Electricity Is the Higher-Value Product


Heat-to-heat leads the application split at 46.00 percent of 2025 sales, worth USD 31.28 billion, and reaches USD 64.44 billion by 2035 at 7.5 percent a year. It leads because reusing heat inside the plant is the simplest option. Heat-to-power holds 36.00 percent, worth USD 24.48 billion, and grows faster at 9.7 percent to USD 61.75 billion, nearly closing the gap. Preheating, at 18.00 percent and 7.3 percent growth, is the slowest, because many plants already preheat combustion air.


The companies moving first have recognised that electricity is more flexible than heat. Recovered heat must be used at the right temperature, at the right time, near the source. Electricity can be used anywhere on site, sold to the grid or used to replace purchased power with a higher carbon footprint. SRI's research notes that higher electricity prices and carbon costs make that conversion worth the extra equipment.


That shift changes the sale. A heat exchanger is sold on efficiency and price to a plant engineer; a heat-to-power system is sold on avoided electricity cost and emissions to a plant manager and a finance team.


"A plant can only reuse so much heat at the right temperature. Electricity has no such limit, and that is why the value in waste heat is moving from the pipe to the generator."

Takeaway on strategy. Position heat-to-power as the growth line. Build business cases on avoided electricity purchases, carbon costs and grid export where allowed, and sell them to plant managers and finance teams rather than only to maintenance engineers.


Lesson 2: Low Temperature Heat Is the Next Frontier


Medium temperature heat from 230 to 650 C holds the largest share at 41.00 percent, because it covers the hot exhaust of boilers, kilns, dryers and engines where steam and organic Rankine systems both work well. But many of the easiest projects have been done, which explains growth of 7.8 percent. Low temperature heat below 230 C holds 38.00 percent and grows fastest at 9.3 percent, because new technology has changed its value. High temperature heat above 650 C holds 21.00 percent and grows at 7.1 percent, the slowest of the three bands.


The technology split follows the temperature split. Organic Rankine cycle systems grow at 10.3 percent, from USD 14.96 billion in 2025 to USD 39.86 billion in 2035, because they turn low and medium temperature heat into power with compact, packaged units. Thermoelectric generators grow fastest at 12.1 percent, from USD 5.44 billion to USD 17.04 billion, because they have no moving parts and suit remote or small sources. Steam Rankine cycle, at 22.00 percent and 6.8 percent growth, remains the choice for large, hot streams in steel and cement but grows slowest of the large technologies because few new large sites are being built.


Takeaway on technology. Invest in organic Rankine cycle and thermoelectric products for heat below 230 C, where the recoverable pool is large and largely untouched. Standardise designs for common low temperature sources such as dryers, compressors and engine jackets, and treat steam Rankine as a project business for large greenfield sites.


Lesson 3: Cement and Glass Grow Fastest, Steel Pays Today


Steel and metals hold the largest end-use share at 22.00 percent, but grow at only 7.7 percent because many steel plants already recover heat and new capacity is concentrated in a few countries. Chemicals and petrochemicals hold 21.00 percent and grow at 8.3 percent, in line with the market. Cement holds 17.00 percent and grows at 9.0 percent, glass holds 10.00 percent and grows fastest at 9.2 percent, oil and gas holds 14.00 percent at 8.1 percent, and food and beverage and paper and pulp each hold 8.00 percent, growing at 8.9 percent and 7.5 percent.


SRI's research explains why cement and glass lead: both run continuous high temperature furnaces with hot exhaust that is easy to reach. A kiln or a glass tank runs around the clock for years, which gives a recovery system steady heat and a predictable payback. Both industries are also under strong pressure to cut emissions, and lower-carbon materials are a growing part of the green building materials market.


"Steel is where waste heat recovery proved itself. Cement and glass are where it will grow, because their furnaces never stop and their carbon bills keep rising."

Takeaway on sales. Target cement and glass for growth and steel and chemicals for scale. Build reference projects in continuous-process industries with steady exhaust, offer performance guarantees tied to recovered energy, and use emissions reporting as part of the value case.


Lesson 4: Packaged Systems Beat Custom Projects


SRI's research names high upfront cost and payback risk as the largest restraint, removing 1.0 point, and site integration complexity as the second, removing 0.8 points. Both point in the same direction. A custom recovery project takes engineering time, interrupts production during installation and carries uncertainty about how much heat will actually be recovered. Operators with short planning cycles often prefer smaller heat exchanger projects, which pay back faster, and that is one reason heat exchangers still hold 46.00 percent of sales.


The companies moving first reduce that friction. Packaged organic Rankine cycle units, skid-mounted heat exchangers and standard interfaces shorten installation and make performance easier to predict. Some suppliers also take on payback risk through energy service contracts, where the operator pays for recovered energy rather than for equipment. That model fits the same logic that is driving electrification of commercial hot water through heat pumps: lower the upfront cost and let measured savings pay for the system.


Takeaway on product and commercial model. Offer packaged, modular recovery units that install during planned shutdowns. Combine them with metering, performance guarantees and energy-as-a-service contracts so that the operator buys recovered energy, not equipment risk.


Lesson 5: Asia Pacific Is Where New Capacity Is Built


Asia Pacific leads with 42.00 percent of 2025 sales, worth USD 28.56 billion, and is also the fastest growing region at 9.4 percent, reaching USD 70.20 billion by 2035. It combines efficiency programmes with new capacity in cement, steel and chemicals, and new plants can design recovery in from the start rather than retrofitting it later. Europe holds 26.00 percent, worth USD 17.68 billion, and grows at 7.5 percent to USD 36.47 billion. North America holds 22.00 percent, and both Western regions grow below the market rate.


The supplier base reflects a market with room for specialists. Siemens Energy leads with an estimated 9.0 percent share, followed by GE Vernova at 8.0 percent, Mitsubishi Heavy Industries at 7.0 percent, ABB at 6.0 percent, Alfa Laval at 5.5 percent, Thermax at 5.0 percent and Ormat Technologies at 4.5 percent. India's Thermax serves a fast growing home market, while Siemens Energy, Alfa Laval and Wartsila are based in Europe and compete on efficiency and service.


The capabilities that decide who captures this demand are specific:


  • Heat-to-power systems sold on avoided electricity and carbon cost.

  • Organic Rankine cycle and thermoelectric products for heat below 230 C.

  • Reference projects in cement, glass and other continuous-process industries.

  • Packaged, modular units with performance guarantees and service contracts.

  • Local engineering and manufacturing in Asia Pacific, where new plants are built.


Companies evaluating these competitive dynamics in greater detail can use SRI's Industrial Waste Heat Recovery Systems Market analysis to assess technology, application, temperature, end-use and regional segments and the positioning of the leading energy equipment companies.


Five lessons framework for industrial waste heat recovery: electricity is the higher-value product, low temperature heat is the next frontier, cement and glass grow fastest, packaged systems beat custom projects, Asia Pacific builds new capacity

Takeaway on go-to-market. Win design-in positions on new Asia Pacific plants through partnerships with engineering contractors and local manufacturing. In Europe and North America, focus on retrofits driven by carbon costs and efficiency rules, with packaged units and service contracts that lower the payback hurdle.


Where the Opportunity Is Concentrating


Value is moving toward power generation, toward lower temperatures, toward continuous-process industries and toward Asia Pacific.


By technology, heat exchangers lead at 46.00 percent, organic Rankine cycle grows at 10.3 percent and thermoelectric generators grow fastest at 12.1 percent.


By application, heat-to-heat leads at 46.00 percent, while heat-to-power grows faster at 9.7 percent and nearly closes the gap by 2035.


By temperature, medium temperature heat leads at 41.00 percent, and low temperature heat grows fastest at 9.3 percent.


By end use, steel and metals lead at 22.00 percent, while glass at 9.2 percent and cement at 9.0 percent grow fastest.


By geography, Asia Pacific leads at 42.00 percent and grows fastest at 9.4 percent, while Europe and North America grow below the market rate.


At the Horizon: What to Watch Over the Next Three Years


Carbon prices in heavy industry. One indicator worth watching is the carbon cost faced by cement, glass and steel plants, because it sets the payback on every recovery project.


Low temperature power costs. The cost per kilowatt of packaged organic Rankine cycle and thermoelectric units will decide how quickly the large pool of heat below 230 C is tapped.


Energy service contracts. The strategic question is shifting from whether a plant can afford recovery equipment to whether a supplier will finance it against measured savings.


"The cheapest energy in a factory is the energy it has already paid for and thrown away. The next decade will reward the companies that make it easy to keep."

The Strategic Revenue Opportunity


For equipment makers, the task is to move from heat exchangers toward heat-to-power systems and low temperature technology. For engineering firms, the priority is reference projects in cement, glass and chemicals and design-in positions on new Asia Pacific plants. For plant operators, the opportunity is lower fuel and carbon costs with measurable returns. For investors, the signal is a large, steady market with a clear mix shift toward faster-growing technologies.


Market intelligence turns these questions into decisions. Segment-level sizing shows where technology, temperature and end-use value is concentrating, competitive analysis shows how energy equipment groups and specialists are positioned, and regional analysis shows where new industrial capacity will pull demand first. This is the path from market signals to strategic insight to revenue impact.


Takeaway on revenue. Treat the industrial waste heat recovery market as four revenue pools: heat exchangers sold on price and payback, heat-to-power systems sold on avoided electricity and carbon cost, low temperature technology sold as packaged units, and service and energy-as-a-service contracts sold on measured savings. Each needs its own sales model. Enter where furnaces run continuously and carbon bills are rising.


The Next Leg: Preparing for the Journey Ahead


The defining shift in industrial waste heat recovery is that lost heat has become a priced resource. Carbon costs and efficiency rules have turned the stack into a source of avoided cost, and new technology has widened the pool of usable heat. The companies moving first are not the ones with the largest heat exchangers; they are the ones turning heat into power, opening low temperature sources, targeting cement and glass, packaging their systems and building where new capacity rises.


The next three years will decide which suppliers own the efficiency layer of heavy industry. Decision-makers should shift portfolios toward heat-to-power, standardise low temperature products and take on payback risk where it wins contracts. Companies evaluating growth opportunities in this market can use Strategic Revenue Insights' Industrial Waste Heat Recovery Systems Market report to assess market size, competitive dynamics, regional opportunities and strategic growth priorities.



Frequently Asked Questions


How big is the industrial waste heat recovery market?


Strategic Revenue Insights values the global industrial waste heat recovery systems market at USD 68.00 billion in 2025 and forecasts USD 150.94 billion by 2035, an 8.3 percent compound annual growth rate. Asia Pacific is the largest region at 42.00 percent of 2025 sales and also the fastest growing at 9.4 percent.


What is driving industrial waste heat recovery?


According to Strategic Revenue Insights, energy cost and carbon pricing add 2.6 percentage points a year to growth and efficiency mandates add 2.2 points. High upfront cost and payback risk remove 1.0 point, and site integration complexity removes 0.8 points from annual growth.


Which waste heat recovery technology grows fastest?


Thermoelectric generators grow fastest at 12.1 percent a year, followed by organic Rankine cycle systems at 10.3 percent, according to Strategic Revenue Insights. Heat exchangers remain the largest technology at 46.00 percent of 2025 sales, while steam Rankine cycle grows slowest of the large technologies.


Why is heat-to-power growing faster than heat-to-heat?


Heat-to-power grows at 9.7 percent a year against 7.5 percent for heat-to-heat, according to Strategic Revenue Insights, because higher electricity prices and carbon costs make converting recovered heat into electricity worth the extra equipment. Electricity can be used anywhere on site, unlike heat.



About the authors: This article was prepared by the Strategic Revenue Insights research team, which combines market intelligence, competitive analysis and strategic advisory for growth-stage, mid-market and enterprise organisations across the construction and manufacturing sector.


Sector analyst: Lukas Schmidt, Technology and Infrastructure Analyst. Our market estimates combine primary research (interviews, surveys and expert panels) with secondary data (industry reports, databases and public disclosures); read more about how Strategic Revenue Insights works. To discuss this market with our analysts, contact our team.


Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page